Reviewed

Charles D. Fulhage and Donald L. Pfost
Department of Agricultural Engineering

A properly calibrated irrigation system can be an efficient and uniform method for land application of liquid nutrients. Application should be done at a time and at a rate so that polluted runoff does not enter the waters of the state. Total nitrogen applied annually must not exceed the design for an approved system. Thus, depth of annual application depends upon the nutrient (nitrogen) analysis of the effluent.

Three performance characteristics are critical to proper land application of lagoon effluent by irrigation. These performance characteristics are determined by site conditions and requirements as shown in Table 1.

Table 1

Performance characteristicDetermined by
Sprinkler application rateSoil infiltration rate or soil permeability
Depth of application per irrigation eventSoil water holding capacity (depends on soil type and soil moisture content at time of irrigation)
Total depth of effluent applied annuallyAmount of nitrogen or other limiting nutrient allowed annually under nutrient management plan

Sprinkler application rate is a characteristic of sprinkler hardware and operating parameters (i.e., nozzle type, size, trajectory, and pressure). Hence sprinklers should be selected to be compatible with soil infiltration rate or permeability. If sprinkler application rate is higher than soil infiltration rate, the possibility for runoff is increased. Since runoff must be prevented when irrigating lagoon effluent, sprinklers are often selected for the lowest application rate possible.

Depth of application per irrigation event should be matched to the water holding capacity of the soil (Table 2). Exceeding the water holding capacity of the soil can result in runoff and contamination of surface water. Depth of application is determined by duration of operation in the case of stationary sprinklers, and by travel speed in the case of traveling sprinklers.

Table 2
Available water holding capacity of various soils

Soil typeMoisture capacity per feet of soil depth
Coarse sands0.25 to 0.75 inches
Fine sands0.75 to 1.00 inches
Loamy sands1.10 to 1.20 inches
Sandy loams1.25 to 1.40 inches
Fine sandy loam1.50 to 2.00 inches
Silt loam2.00 to 2.50 inches
Silty clay loam1.80 to 2.00 inches
Silty clay1.50 to 1.70 inches
Clay1.20 to 1.50 inches

The total depth of effluent applied annually should provide the target amount of nutrients to the receiving area on a yearly basis as specified in the nutrient management plan. This may be accomplished in a single irrigation event, or may require several separate applications, depending on site conditions.

Application rate

The maximum allowable rate of application (inches per hour) to prevent runoff depends on the intake rate of the soil. Intake rate of an initially dry soil typically decreases at a high rate as water is added and approaches the permeability of the soil. County soil surveys give the permeability of soils in inches per hour and the available water holding capacity in inches per inch. The total amount (inches) of an application depends upon the water holding capacity (moisture deficit) of the soil at the time of application. Contact your local Natural Resources Conservation Service office for a current soil survey. If soil surveys are not available, the data in Tables 2 and 3 may be used as a guide. Table 4 is a guide for determining soil moisture content by feel and appearance.

Table 3
Maximum water application rates (From MWPS18). Soils usually absorb water at a faster rate if applied in light applications (3/4-inch to 1-1/2-inch or less) when the soil is dry

Soil characteristics0 percent to 5 percent slope
CoverBare
Clay; very poorly drained0.3 inches per hour0.15 inches per hour
Silty surface; poorly drained, clay and claypan subsoil0.4 inches per hour0.25 inches per hour
Medium textured surface soil; moderately to imperfectly drained profile0.5 inches per hour0.30 inches per hour
Silt loam, loam and very sandy loam; well to moderately well drained0.6 inches per hour0.40 inches per hour
Loamy sand, sandy loam, or peat; well drained0.9 inches per hour0.60 inches per hour
Reduce application rates on sloping ground
SlopeApplication rate reduction
0 to 5 percent0 percent
6 to 8 percent20 percent
9 to 12 percent40 percent
13 to 20 percent60 percent
over 20 percent75 percent

Table 4
Guide for determining soil moisture content (From MWPS18)

Moisture conditionPercent of available moisture remaining in soilSoil texture
Sand to sandy loamLoam to silt loamClay loam to clay
Dry0 percent
Wilting point
Dry, loose, flows through fingers.Powdery, sometimes slightly crusted but easily broken into powder.Hard, baked, cracked; difficult to break into powder.
Low50 percent or lessLoose, feels dryForms a weak ball when squeezed but will not stick to tools.Pliable, but not slick, balls under pressure. Sticks to tools.
Fair50 percent to 75 percentBalls under pressure but seldom holds together when bounced in hand.Forms a ball somewhat plastic, sticks slightly with pressure. coes not stick to tools.Forms a ball, ribbons out between thumb and forefinger, has a slick feeling.
Good75 percent to 100 percentForms a weak ball, breaks easily when bounced in the hand; can feel moistness.Forms a ball, very pliable, sticks readily, clings slightly to tools.Easily ribbons out between thumb and forefinger, has a slick feeling, very sticky.
Ideal100 percentSoil mass clings together. Upon squeezing, outline of ball is left on hand.Wet outline of ball is left on hand when soil is squeezed. Sticks to tools.Wet outline of ball is left on hand when soil is squeezed. Sticky enough to cling to fingers.

Table 5
Discharge of big gun nozzles (From MWPS18). Taper bore nozzles have the greatest stream integrity, longest throw distance and minimum wind distortion. Ring nozzles have better stream breakup for lower pressure operation and delicate crops. Ring nozzles catch animal hair on the nozzle lip and plug more often than taper bore nozzles. Diameter is the size of the area irrigated; gpm is the application rate

Nozzle trajectory
 24 degrees27 degrees
Taper bore0.6 inch0.7 inch0.9 inch1.1 inches1.3 inches1.5 inches1.75 inches
Ring nozzle 0.86 inch1.08 inches1.26 inches1.41 inches1.74 inches1.93 inches
PressuregpmDiametergpmDiametergpmDiametergpmDiametergpmDiametergpmDiametergpmDiameter
50 psi74225 feet100250 feet165290 feet255330 feet      
60 psi81240 feet110265 feet182305 feet275345 feet385390 feet515430 feet695470 feet
70 psi88250 feet120280 feet197320 feet295360 feet415410 feet555450 feet755495 feet
80 psi94260 feet128290 feet210335 feet315375 feet445430 feet590470 feet805515 feet
90 psi100270 feet135300 feet223345 feet335390 feet475445 feet626485 feet855535 feet
100 psi106280 feet143310 feet235355 feet355400 feet500460 feet660500 feet900550 feet
110 psi111290 feet150320 feet247365 feet370410 feet525470 feet695515 feet945565 feet
120 psi  157330 feet258375 feet385420 feet545480 feet725530 feet985580 feet
130 psi        565485 feet755540 feet1025590 feet

The average application rate of an irrigation sprinkler varies with nozzle opening size, number of nozzles (usually 1 to 3 per sprinkler), pressure and wetted diameter. Sprinklers with one large nozzle will reduce clogging problems when irrigating with animal wastewater. Big guns generally have only one large nozzle, specifically designed for long-throw distance. Wetted diameter varies with nozzle size, pressure and sprinkler angle. Data for sprinklers and big guns can be found in the manufacturer's literature. Table 5 has general data for big guns, if manufacturer's data are not available for planning.

Application rate varies with distance from the sprinkler (or gun). If the sprinkler produces a triangular application pattern, proper spacing should achieve a nearly uniform application depth. Sprayer application pattern can vary with operating pressure. To attain acceptable application uniformity with multiple sprinkler setups, the sprinkler spacing should be 65 percent to 80 percent of the wetted diameter. Overall uniformity can be affected by wind velocity. If possible, try to irrigate when the wind is under 5 mph. Sprinkler spacing variations with wind are given in Table 6. High trajectory sprinklers are used for low wind conditions to obtain maximum distance of throw. Low trajectory sprinklers will give shorter distance of throw and a minimum of pattern distortion.

Table 6
Typical sprinkler spacing with adjustment for wind

Wind speedSprinkler spacing
0 miles per hour70 percent of wetted diameter
10 miles per hour60 percent of wetted diameter
over 10 miles per hour50 percent of wetted diameter

Calibration of stationary big gun sprinkler systems

The average rate of application of a stationary sprinkler, operating full circle, is calculated as follows:

R, inches per hour =gpm x 96.3
wetted area
=______gpm x 96.3______
0.7854 x (wetted diameter, square feet

The average rate and depth of application from multiple settings of a stationary gun or a solid set system vary with the net area covered from a given sprinkler location. Sprinkler locations are usually in a square or rectangular pattern but may be in a triangular pattern (Figure 1).

Effect of sprinkler spacing and arrangementFigure 1
Effect of sprinkler spacing and arrangement. Note that the rectangular pattern requires closer spacing to achieve full coverage and reasonable uniformity.

Examples

The following equations are aids for selecting sprinkler equipment and developing management procedures for sprinkler operation.

System flow rate required to pump a lagoon in a given number of 8-hour days

Equation 1

Q = 0.0156 x V/N

Where
Q = system flow rate, gallons per minute
V = lagoon pumpdown volume, cubic feet
N = number of 8-hour days to pump lagoon
Average application rate of a single-set, or multi-set sprinkler system For a single-set sprinkler:

Equation 2

AR = 122.6 x Q/(WD)2

For a multi-set sprinkler system:

Equation 3

AR = 96.3 x Q/(WD x SP)2

Where
AR = average application rate, inches per hour
Q = system flow rate, gallons per minute
WD = wetted diameter of sprinkler, feet
SP = sprinkler spacing, fraction of wetted diameter
Time to operate system to obtain a given depth of application

Equation 4

TD = D/AR

Where
TD = time to operate sprinkler to obtain a given depth of application, hour
D = depth of application, in
AR = application rate, inches per hour
Time to operate system to obtain a given amount of nutrient per acre

Equation 5

TN = 0.0368 x NA/(AR x C)

Where
TN = time to operate sprinkler to obtain a given amount of nutrient per acre
NA = target nutrient application, pounds per acre
AR = application rate, inches per hour
C = nutrient content in lagoon effluent, pounds per 1,000 gallons
Example 1

A 200-cow dairy has an annual pumpdown volume of 400,000 cubic feet. It is desired to accomplish this pumpdown in 12 days of eight hours pumping time each. Select a single-set, stationary gun sprinkler to apply the effluent to a soil-plant filter with a medium textured silty clay soil that is moderately drained. The receiving area will have a vegetative cover, and slopes are in the range of 6 percent to 8 percent. Laboratory tests show a nitrogen concentration of 2.8 pounds per 1,000 gallons in the lagoon effluent. Target annual nitrogen application is 140 pounds per acre. Use the above equations and data in Tables 2, 3, 4 and 5; select the sprinkler and calculate the appropriate operating time for each sprinkler setting, and the total operating time to achieve the target nitrogen application rate.

  • Calculate the system flow rate needed to pump the lagoon in 12 days using Equation 1.

Q = 0.0156 x 400,000 ÷ 12 = 520 gallons per minute

  • Select a sprinkler that will give this flow rate from Table 5.

Two of the 27-degree trajectory nozzles listed would give the desired flow rate. A 1.41-inch ring nozzle operating at 110 psi gives 525 gpm with a wetted diameter of 470 feet. A 1.74-inch ring nozzle operating at 60 psi gives 515 gpm with a wetted diameter of 430 feet.

  • Check sprinkler application rate for compatibility with soil infiltration rate. From Table 4, a moderately drained, medium textured silty clay soil has a maximum application rate of 0.5 inches per hour with a vegetative cover. This rate should be reduced by 20 percent since slopes are 6 percent to 8 percent. Target application rate is then:

0.5 inches per hour x 0.8 = 0.4 inches per hour

Calculate application rate for the nozzles noted previously using Equation 2 for single-set operation.

1.41-inch ring nozzle

AR = 122.6 x 525 ÷ (470)2 = 0.29 inches per hour

1.74-inch ring nozzle

AR = 122.6 x 515 ÷ (430)2 = 0.34 inches per hour

Since both of these nozzles have suitable application rates, (less than 0.4 inches per hour) selection might be based on pressure requirement or some other factor. Note that a gun spacing of 70 percent of wetted diameter (multiple gun set) would increase application rate by about 60 percent. If application rate is greater than the maximum for a given soil, take care to irrigate with light applications when the soil is dry. Assume that the 1.41-inch ring nozzle will be used in this example.

  • Calculate time to operate sprinkler to obtain a given depth of application. Assume that irrigation will take place when the soil is at the 50 percent moisture condition, and that the applicable root zone depth is 1.5 feet. From Table 2, a silty clay soil has a water holding capacity of 1.6 inches per foot depth of soil. The depth of water to apply is calculated as follows.

Depth = 1.6 inches [er feet x 1.5 feet x 0.5 = 1.2 inches

Calculate the time to apply 1.2 inches using Equation 4.

TD = 1.2 ÷ 0.29 = 4.1 hours

The sprinkler should be operated 4.1 hours to achieve the target application depth of 1.2 inches.

  • Calculate the total time required to apply 140 pounds of nitrogen per acre annually, using Equation 5.

TN = 0.0368 x 140 ÷ (0.29 x 2.8) = 6.3 hours

Since the operating time for nitrogen is greater than the operating time for soil conditions, the total annual operating time of 6.3 hours could be broken into two equal irrigation events of 3.15 hours each. This approach would minimize the risk of runoff, and may allow irrigating on soil with a higher moisture content, since less water will be applied each time.

Calibration of traveling big gun sprinkler systems

The sprinklers on traveling big guns are usually equivalent to stationary big guns. However, the sprinkler may be operated part-circle to keep a dry travel lane ahead of the traveling gun. This increases the instantaneous application rate due to the decreased area of application, and also slightly affects the uniformity of application. (The application rate for part-circle gun operation may be found by dividing the rate in inches per hour for full-circle operation by the fraction of full-circle the gun is operated.) The depth of liquid applied by a traveling gun depends on the flow rate (gpm), the lane spacing and the travel speed. Table 7 has depth of water applied as a function of these variables. Table 8 shows acres irrigated per set as a function of lane spacing and travel distance. Table 9 recommends lane spacings for windy conditions.

Table 7
Water applied by traveling big guns (From MWPS18). Average water depth applied, inches = (1.605 x sprinkler gpm) ÷ (lane spacing, feet x travel speed, feet per minute). To convert table to gallons per acre, multiply by 27,150

Sprinkler rateTravel lane spacingTravel speed, feet per minute
0.40.51246810
Water applied, inches
50 gpm105 feet1.91.50.760.380.190.130.0960.076
125 feet1.61.30.640.320.160.110.080.064
155 feet1.31.00.520.260.130.090.0650.052
60 gpm110 feet2.21.80.880.440.220.150.1090.088
130 feet1.91.50.740.370.190.120.0930.074
160 feet1.51.20.600.300.150.100.0750.060
70 gpm115 feet2.42.00.980.490.240.160.1220.098
140 feet2.01.60.800.400.200.130.1000.080
170 feet1.71.30.660.330.170.110.0830.066
80 gpm120 feet2.72.11.070.540.270.180.1340.107
145 feet2.21.80.890.440.220.150.1110.089
180 feet1.81.40.710.360.180.120.0890.071
90 gpm125 feet2.92.31.160.580.290.190.1440.116
150 feet2.41.90.960.480.240.160.1200.096
185 feet2.01.60.780.390.200.130.0980.078
100 gpm165 feet2.41.90.970.490.240.160.120.10
200 feet2.01.60.800.400.200.130.100.08
200 gpm165 feet4.93.91.91.00.50.320.240.20
200 feet4.03.21.60.80.40.270.200.16
300 gpm200 feet6.04.82.41.20.60.400.300.24
270 feet4.53.61.80.90.40.300.220.18
400 gpm240 feet6.75.42.71.30.70.450.330.27
300 feet5.44.32.11.10.50.360.270.21
500 gpm270 feet7.45.93.01.50.70.500.370.30
330 feet6.14.92.41.20.60.410.300.24
600 gpm270 feet8.97.13.61.80.90.590.450.36
330 feet7.35.82.91.50.70.490.370.29
700 gpm270 feet10.48.34.22.11.00.690.520.42
330 feet8.56.83.41.70.90.570.430.34
800 gpm300 feet10.78.64.32.11.10.710.540.43
360 feet8.97.13.61.80.90.590.450.36
900 gpm300 feet12.09.64.82.41.20.800.600.50
360 feet10.08.04.02.01.00.670.500.40
1,000 gpm330 feet12.29.74.92.41.20.810.610.50
400 feet10.08.04.02.01.00.670.500.40

Table 8
Acres irrigated per setting by traveling big guns (from MWPS18). For best watering uniformity, make lane spacing 50 percent to 70 percent of the sprinkler wetted diameter

Lane spacing600 feet ravel distance1,000 feet travel distance
100 feet1.5 acres per set2.3 acres per set
120 feet1.8 acres per set2.8 acres per set
140 feet2.1 acres per set3.2 acres per set
160 feet2.4 acres per set3.7 acres per set
180 feet2.7 acres per set4.1 acres per set
200 feet3.0 acres per set4.6 acres per set
220 feet3.3 acres per set5.1 acres per set
240 feet3.6 acres per set5.5 acres per set
260 feet3.9 acres per set6.0 acres per set
280 feet4.2 acres per set6.4 acres per set
300 feet4.5 acres per set6.9 acres per set
320 feet4.8 acres per set7.3 acres per set
340 feet5.2 acres per set7.8 acres per set
360 feet5.5 acres per set8.3 acres per set
380 feet5.8 acres per set8.7 acres per set
400 feet6.1 acres per set9.2 acres per set

Table 9
Maximum lane spacing for traveling big guns (From MWPS18)

Sprinkler wetted diameter of sprinklerPercent of wetted diameter
50556065707580
Wind over 10 miles per hourWind up to 10 miles per hourWind up to 5 miles per hourNo wind
200 feet100110120130140150160
250 feet125137150162175187200
300 feet150165180195210225240
350 feet175192210227245262280
400 feet200220240260280300320
450 feet225248270292315338360
500 feet250275300325350375400
550 feet275302330358385412440
600 feet300330360390420  

The following equations are aids in calibrating and managing the operation of traveling gun sprinklers.

Average application rate of a traveling gun sprinkler:

Equation 6

AR = 122.6 x Q ÷ (WD x WD x F)

Where
AR = average application rate, inches per hour
Q = flow rate, gallons per minute
WD = wetted diameter of sprinkler, feet
F = fraction of full circle operation
Speed to operate a traveling gun sprinkler to obtain a given application depth, inches

Equation 7

S = 1.605 x Q ÷ (SP x D)

Where
S = travel speed, feet per minute
Q = flow rate, gallons per minute
SP = traveling gun lane spacing, feet
D = depth of water applied
Depth of water to apply to obtain a given nutrient application rate

Equation 8

D = 0.0368 x NA ÷ C

Where
D = depth of water to apply, inches
NA = target nutrient application, pounds per acre
C = nutrient content in lagoon effluent, pounds per 1,000 gallons
Example 2

A traveling gun is to be used to apply lagoon effluent under the conditions noted in Example 1. Assume that the nozzle will be operated part-circle with a 45-degree open segment to maintain a dry travel lane. Assume the traveling gun will use the same nozzle selected in Example 1. Calculate the gun travel speed required to apply the proper depth with the 50-percent soil-moisture condition. Also calculate the total depth-to-apply annually to obtain 140 pounds of nitrogen per acre.

  • Check sprinkler application rate for compatibility with soil infiltration rate. The fraction of full circle operation is

(360 - 45) ÷ 360 = 0.875

Using the 1.41-inch ring nozzle, and Equation 6.

AR = 122.6 x 525 ÷ (470 x 470 x 0.875) = 0.33 inches per hour

Since this is less than the 0.4 inch per hour soil infiltration rate, the application rate is acceptable without modification.

  • Calculate the travel speed required to apply the proper depth (1.2 inches) under 50 percent soil-moisture conditions. Use Equation 7 and assume a lane spacing of 70 percent of wetted diameter.

S = 1.605 x 525 ÷ (470 x 0.7 x 1.2) = 2.13 feet per minute

  • Calculate the depth of water to apply to obtain 140 pounds of nitrogen per acre, using Equation 8.

D = 0.0368 x 140 ÷ 2.8 = 1.84 inches

Since this depth is greater than the 1.2 inches for the 50 percent soil-moisture condition, the target nitrogen application will have to be obtained using two passes, or with a single pass under drier soil conditions. If two passes were used, each applying 1.84 ÷ 2 = 0.92 inches, gun travel speed would be calculated as follows using Equation 7.

S = 1.605 x 525 ÷ (470 x 0.7 x 0.92) = 2.78 feet per minute

Evaluation of application amount and uniformity

The calibration procedures above are predicated on the assumed performance of sprinklers operated at certain pressures and sprinkler spacings. To verify that the assumed performance is achieved, catch-cans for stationary sprinklers can be spaced as shown in Figures 2 and 3. Run tests until the average depth of wastewater in the cans is at least 1 inch; longer tests will reduce errors in measuring small amounts. Catch-cans for traveling guns can be placed in a line perpendicular to the direction of travel and between two adjacent travel lanes. Catch-cans should not be more than 10 feet apart. (Source: Reference number 3.)

Catch-container for solid set (block) sprinkler layoutFigure 2
Catch-container for solid set (block) sprinkler layout.
 

Catch-container layout for solid set (triangular) sprinkler layoutFigure 3
Catch-container layout for solid set (triangular) sprinkler layout.
 

For further information

  • American Society of Agricultural Engineers. 1980. Design and Operation of Farm Irrigation Systems. ASAE Monograph number 3. 2950 Niles Road, St. Joseph, Mich.
  • University of Arkansas Extension Publication FSA 1022-S459. 1993. Calibrating Traveling Big Gun Sprinklers for Manure Applications. University of Arkansas Cooperative Extension Service, Little Rock, Ark.
  • University of Arkansas Extension Publication FSA 1023-S460. 1993. Calibrating Stationary Big Gun Sprinklers for Manure Applications. University of Arkansas Cooperative Extension Service, Little Rock, Ark.
  • U.S. Department of Agriculture, Natural Resources Conservation Service. Agricultural Waste Management Field Handbook.
Publication No. EQ327